Rode NT2000 Large-Diaphragm Multipattern Condenser Microphone
Features at a Glance
- True condenser (externally biased)
- Large 1" HF1 capsule with gold-sputtered dual diaphragms
- The polar pattern is continuously variable between omnidirectional, cardioid, and figure-8
- Continuously variable pad and high-pass filter
- Self-noise of only 7 dBA
- Transformerless JFET active circuitry
- Wide dynamic range
- XLR 3-pin output connector
- Runs on phantom power
- High-strength welded and heat-treated steel mesh head
- Internally shock-mounted capsule
Large-Diaphragm True Condenser
This true condenser (externally biased) features a 1" gold-sputtered, dual-diaphragm capsule that provides a broad frequency response, wide dynamic range, and excellent signal-to-noise ratio.
Variable Polar Pattern
The NT2000's polar pattern is continuously variable from omnidirectional to cardioid to figure 8. As a result, the NT2000 offers excellent versatility for single-source close miking, dual-source pickup, room ambiance capture, and more.
Variable Pad
The pad, which reduces the input level to the microphone's in-built preamp, can be continuously adjusted from 0 to -10 dB. This is very useful when recording loud sound sources (such as close miking of drums or amplifiers) to avoid overloading the microphone's preamplifier.
Variable High-Pass Filter
Choose any setting between 20 and 150 Hz to cut the level of the selected frequency and below by 3 dB. This control is useful for selecting the cut-off point for potentially offending low frequencies such as traffic noise and floor vibrations. It can also be used on vocals to achieve a limited response for a "different" sound.
Transformerless Output
The transformerless JFET output electronics result in an ultralow-noise output (just 7 dBA) while maintaining maximum signal gain.
48V Phantom Power
The NT2000 operates reliably on 24 or 48-VDC phantom power, which can be supplied via most XLR-connected mic preamps, mixer channels, or audio interfaces.
Shockmount and Case
The NT2000's accessory package includes a studio-grade shock mount that reduces stand-borne vibration and a hard shell carry case.
Specifications
Microphone
| Primary Applications | Studio Recording |
| Form Factor | Large Diaphragm Mic / Stand/Boom Mount |
| Intended Sound Sources | Vocals, Speech/Voice Over, Instrument |
| Sound Field | Mono |
| Operating Principle | Pressure Gradient |
| Capsule | Condenser |
| Diaphragm | 1" / 25.40 mm |
| Polar Pattern | Cardioid, Figure-8, Omnidirectional |
| Pattern Selection | Continuously Variable (Adjustable on Mic) |
| Orientation | Side Address |
| Circuitry | Solid-State (JFET) |
| Pad | -10 dB |
| High-Pass Filter |
150 Hz, 3 dB/Octave 20 Hz, 3 dB/Octave |
| Tone Adjustment | None |
| Gain Adjustment | None |
| Indicators | None |
| On-Board Controls | High-Pass Filter, Pad, Polar Pattern |
| Windscreen | None |
Performance
| Frequency Range | 20 Hz to 20 kHz |
| Maximum SPL | 147 dB SPL (1 kHz, 1% THD, 1-Kilohm Load) 157 dB SPL (1 kHz, 1% THD, 1-Kilohm Load, with Pad) |
| Impedance | 200 Ohms |
| Sensitivity | -36 dBV/Pa at 1 kHz |
| Output Level | 15 mV (Max, 1 kHz) |
| Dynamic Range | 140 dB |
| Signal-to-Noise Ratio | 87 dB SPL (1 kHz) |
| Equivalent Noise Level | 7 dB A-Weighted |
Connectivity
| Output Connectors (Analog) | 1 x XLR 3-Pin Male (on Mic) |
| Headphone Connector | None |
Power
| Bus Power | None |
| Operating Voltage | 24 V (Phantom Power) 48 V (Phantom Power) |
Physical
| Color | Silver |
| Mounting | Shockmount (Included) |
| Included Case | Hard Case |
| Included Filters | None |
| Dimensions | ø: 2.2 x L: 8.2" / ø: 55 x L: 208 mm |
| Weight | 1.8 lb / 831 g |
Packaging Info
| Package Weight | 6.05 lb |
| Box Dimensions (LxWxH) | 16 x 13 x 6.4" |
